Wake on Lan what ports forward? - QNAP NAS Community Forum

<?php // // I have used the original PHP code from here: // // Version: 2 // Author of this application: // DS508_customer (http://www.synology.com/enu/forum/memberlist.php?mode=viewprofile&u=12636) // Please inform the author of any…

How To: Wake on LAN / Wake on WAN - …

Wake-on-LAN Issue | THWACK Re: Wake On Lan issue. by bryan on Fri Jul 13, 2007 8:00 am. Thanks for the additional info. OK, so you are just basically broadcasting to all machines on your same subnet, which is equivalent to DNTU's Wake Batch. So I would have to believe this is just a port issue. Try using port 65535 instead of 32767, which appears to be the default UDP ... How to Remotely Turn On Your PC Over the Internet Wake-On-LAN uses UDP. Many utilities use ports 7 or 9, but you can use any port you like for this. ... Port Number: Enter the number of the UDP port you forwarded to the broadcast address . The tool can then send a “magic packet” with the correct information and—if you’ve configured everything correctly—your PC will wake up. Solved: Wake on LAN (WOL) across different VLAN... - Cisco ...

Remotely Wake up your Computers with Wake On Lan Not only do you need Wake On Lan to be enabled, often a setting found under ..... Note that port 9 (UDP) is the most commonly used port for Wake On Lan and ... Bash one-line command to send wake on LAN magic packet without ... This example uses UDP port 4.000. The specific port number seems not to be important on WOL. The above one-line bash command should ... Wake-on-LAN - ArchWiki /etc/systemd/system/[email protected] [Unit] Description=Wake-on-LAN for %i Requires=network.target After=network.target [Service] ExecStart=/usr/bin/ethtool -s %i wol g Type=oneshot [Install] WantedBy=multi-user.target Wake-on-LAN (tutorial) - DD-WRT Wiki

Yes -dport 7 and -sport 7 to set the destination port and source port. – Depicus Nov 7 '10 at 12:39 Your -A might not be IN_FILTER so do a iptables -L to get a list of rules. Solved: Wake on LAN (WOL) across different VLAN... - Cisco ... Solved: Hello there, I am trying to get WOL working across different VLANS on a SG-300-10 Switch in Layer 3 Mode. To achieve this, I've setup an UDP-Relay (GUI menu IP Configuration) for UDP-Port 7 to 255.255.255.255 (this should flood all Wake-On-LAN (WOL) Network Configuration | HOWTO's and ... Wake-on-LAN (WOL) has been used for years as a way for network administrators to turn on PCs remotely. It works by creating and issuing a specially formatted network packet (often referred to as a “magic” packet, and typically generated via a software utility) containing a target PC’s MAC address.

The application by default is set to listen for Magic Packets on UDP port 7. LDMS by default uses UDP port 0. In the Wake on Lan Monitor, set the UDP port to 0. Click Start. Note: In the event the Core is set to use a different port for WoL, use that port. Once started, the Wake On Lan Monitor will go to a 'Connected' state. It is now listening for a Magic Packet on the defined UDP port (in our example UDP port 0).

Waking your PC up over the Internet can come in handy. Doug Reid shows you how. {mospagebreak toctitle= Introduction} {multithumb} Introduction What is Wake ... HP Comware: Forwarding subnet-directed broadcasts for Wake-on [HP]acl number 3001 [HP-acl-adv-3001] rule 10 permit udp source 192.168.200.0 0.0.0.255 destination 10.0.0.255 0 destination-port eq 9 [HP-acl-adv-3001] quit [HP] interface Vlan-interface 99 [HP-vlan99] ip forward-broadcast acl 3001 wake on lan Software - Free Download wake on lan - Top 4… wake on lan Software - Free Download wake on lan - Top 4 Download - Top4Download.com offers free software downloads for Windows, Mac, iOS and Android computers and mobile devices. Visit for free, full and secured software’s. Tweaking4All.com - Remotely Wake up your Computers with Wake On